6 posts / 0 new
Last post
Indy
Offline
Last seen: 2 years 2 months ago
Joined: 03/24/2015 - 07:49
Use of Inputs 5-8 Analog/Freq

I have 6 AEM digital gauges. So can I put 2 of them on the 5-8 Analog/Freq inputs for data logging. Seems like it might be possible according to the manual.

 

Thanks , Rick

 

The analog/frequency 5-8 pages are similar to the Analog 1-4 pages. In addition to measuring voltage signals, Analog/Frequency channels 5-8 are also capable of measuring pulse based signals.

Page 11 of the manul

AEM_PT
Offline
Last seen: 17 hours 46 min ago
Joined: 05/22/2014 - 08:13
If your gauge has a 0-5V

If your gauge has a 0-5V analog output, you can run it to any of the 8 Analog inputs on your AQ-1 Logger.

Indy
Offline
Last seen: 2 years 2 months ago
Joined: 03/24/2015 - 07:49
Thanks for the quick reply!!!

Thanks for the quick reply!!!

Nice to know I can log ALL my gauges then.....excellent !!! smiley

AEM_GN
Offline
Last seen: 3 years 8 months ago
Joined: 02/18/2014 - 09:55
For anyone else that may come

For anyone else that may come by this thread. Here are examples of what you can log on what channels.

CHANNELS 1-4 - 0-5V or optional pullup resistor for RTD/Thermistor-style sensors
Choose up to 4(Sensor Examples)

  • Air/Fuel Ratio 1
  • Air/Fuel Ratio 2
  • Air/Fuel Ratio 3
  • Air/Fuel Ratio 4
  • 0-5V Boost
  • 0-5V Boost After Intercooler
  • 0-5V Boost Before Intercooler
  • 0-5V MAP
  • 0-5V Exhaust Back Pressure
  • 0-5V Crank Case Pressure
  • 0-5V Fuel Pressure
  • 0-5V Oil Pressure
  • 0-5V Clutch Pressure
  • 0-5V Brake Pressure
  • 0-5V Shock Travel Sensor
  • Air Temperature
  • Coolant Temperature
  • Trans Temperature
  • EGT 1
  • EGT 2
  • EGT 3
  • EGT 4

CHANNELS 5-8 - 0-5V, 0-16.5V or Frequency based sensors
Choose up to 4(Examples of sensors)

  • Air/Fuel Ratio 1
  • Air/Fuel Ratio 2
  • Air/Fuel Ratio 3
  • Air/Fuel Ratio 4
  • 0-5V Boost
  • 0-5V Boost After Intercooler
  • 0-5V Boost Before Intercooler
  • 0-5V MAP
  • 0-5V Exhaust Back Pressure
  • 0-5V Crank Case Pressure
  • 0-5V Fuel Pressure
  • 0-5V Oil Pressure
  • 0-5V Clutch Pressure
  • 0-5V Brake Pressure
  • 0-5V Shock Travel Sensor
  • RPM
  • Driveshaft Speed
  • Wheel Speed
  • Turbo Speed>

Switched Digital Inputs 1-3
Choose up to 3(Examples)

  • Clutch Switch
  • Brake Switch
  • Line Lock
  • Nitrous Switch

Serial/GPS
Choose 1(Examples)

  • GPS for Vehicle Speed, GPS Location and Track Mapping - Recommended Garmin 18x 1Hz & 5Hz models(some wiring may be required)
  • Series 1 EMS
  • Series 2 EMS

AEMnet

  • Infinity EMS
  • Wideband Failsafe
  • 4-Channel Wideband UEGO Controller
  • Series 2 EMS
  • EMS-4
Indy
Offline
Last seen: 2 years 2 months ago
Joined: 03/24/2015 - 07:49
Do you sell a sensor for

Do you sell a sensor for driveshaft speed? If not, then how would one go about hooking up one?

Thanks!

Rick

AEM_NS
Offline
Last seen: 1 year 4 months ago
Joined: 06/06/2014 - 09:31
The AQ-1 can only accept

The AQ-1 can only accept square wave frequency inputs which means using a driveshaft speed sensor that is Hall Effect.  You'd supply power and ground to the sensor and then connect the sensor's signal output to one of the frequency inputs of the AQ-1 and then configure the logging channel in the software.  Just be sure to use a Hall sensor.