8 posts / 0 new
Last post
JoseMarmolejo
Offline
Last seen: 6 months 2 weeks ago
Joined: 03/12/2017 - 16:42
EMS4-AQ1-CD7

Hi, 

I have an EMS-4 and wired sensors in GPIO
#1 oilpress
#2 oiltemp
#3 FuelPress
#4 FuelLevel
#5 VVT
#7 Boos solenoid

AEMNet connected AQ1 and AEMnet Conected CD7

how do i get this sensors to show in the CD7 and make sure they log in the AQ1

when i try to configure the  CD7 the Inputs does not show all the PGIO 

only 2, 4, 5, 6, 7 but i need 1, 3?

also some how does not looks like is sending the correct value

help please

 

AEM_HB
Offline
Last seen: 1 week 18 hours ago
Joined: 11/07/2016 - 09:22
Hey Jose, 

Hey Jose, 

We just made a new dbc for you, please load this into the cd-7 using the dash design software and make the following changes to your calibration file in AEM tuner . These changes will allow GPIO 1 and 3 to show up on the CD-7. All of the GPIO channels will show up in the dash as 0-5v, from there you will be able to create a new output to rescale the 0-5v signal into something like oil pressure or fuel level.

AEM 30-6905 EMS-4 SI_GPIO1_GPIO3.dbc

 

JoseMarmolejo
Offline
Last seen: 6 months 2 weeks ago
Joined: 03/12/2017 - 16:42
Thank you, good help, now the

Thank you, good help, now the sreen show allot of numbers on the oilpress for example

i used the sensor AEMconversion but does not seams to work

you have an idea why ?

 

JoseMarmolejo
Offline
Last seen: 6 months 2 weeks ago
Joined: 03/12/2017 - 16:42
also thid data now go to my

also this data now go to my AQ1 but i dont know what chanel is what 

AQ1 show ADCR08, 11, 13, 14, 15, 16, 17, 18 ?

 

JoseMarmolejo
Offline
Last seen: 6 months 2 weeks ago
Joined: 03/12/2017 - 16:42
it is possible to get the GPS

it is possible to get the GPS data from the AQ1 with GPS serial setup in to the CD7 ?

AEM_JG
Offline
Last seen: 19 hours 58 min ago
Joined: 06/03/2016 - 08:12
JoseMarmolejo wrote:

JoseMarmolejo wrote:

also this data now go to my AQ1 but i dont know what chanel is what 

AQ1 show ADCR08, 11, 13, 14, 15, 16, 17, 18 ?

 

ADCR08 = ECU Battery Volts 

ADCR11 = GPIO2 Voltage

ADCR13 = GPIO4 Voltage

ADCR14 = GPIO5 Voltage

ADCR15 = GPIO6 Voltage

ADCR16= GPIO7 Voltage

ADCR17= GPIO1 Voltage

ADCR18= GPIO3 Voltage

JoseMarmolejo
Offline
Last seen: 6 months 2 weeks ago
Joined: 03/12/2017 - 16:42
there is 2 GPIO 2 in your

there is 2 GPIO 2 in your list, and no 3 :(

AEM_JG
Offline
Last seen: 19 hours 58 min ago
Joined: 06/03/2016 - 08:12
JoseMarmolejo wrote:

JoseMarmolejo wrote:

there is 2 GPIO 2 in your list, and no 3 :(

Fixed above