RB26 Aftermarket Crank Sensor | AEM
11 posts / 0 new
Last post
gap450r
Offline
Last seen: 1 month 3 weeks ago
Joined: 10/27/2018 - 21:33
RB26 Aftermarket Crank Sensor

Hello, is there any way I can upgrade the factory Nissan CAS? Im looking to buy this but I was told It could not be setup with the Series 2 30-6620.

Thanks in adavanced,

Gabriel

https://platinumracingproducts.com/pages/platinum-racing-nissan-rb-ignit...

 

 

AEM_NS
Offline
Last seen: 4 hours 8 min ago
Joined: 06/06/2014 - 09:31
No reason why that wouldn't

No reason why that wouldn't work with a Series 2. The output signal is exactly the same as the AEM Nissan CAS disc - 12 crank teeth and a single cam tooth. No difference.

gap450r
Offline
Last seen: 1 month 3 weeks ago
Joined: 10/27/2018 - 21:33
Thanks, so I should connect

Thanks, so I should connect the sesnors to he correct pins for the cam and crank sensor and thats it? no need to reconfigure wizard or anything?

AEM_NS
Offline
Last seen: 4 hours 8 min ago
Joined: 06/06/2014 - 09:31
Right - wire it appropriately

Right - wire it appropriately, set wizard for AEM Nissan CAS disc and then sync the timing and you should be good to go.

gap450r
Offline
Last seen: 1 month 3 weeks ago
Joined: 10/27/2018 - 21:33
Thanks for the help, also i

Thanks for the help, also i can see the Tacho and Speed are way off. I currently have a 1998 240sx with a RB26 swap. Is there anything I can do to fix both issues?

AEM_NS
Offline
Last seen: 4 hours 8 min ago
Joined: 06/06/2014 - 09:31
Tacho output in base cal is

Tacho output in base cal is setup for 6 pulse per cycle. You'll probably need to change it to 4 pulses per cycle - see the Tacho table in the Tacho-Speedo tab.

As best I know it, there's a speed input into the ECU but nothing comes back out that goes to the speedometer so there's nothing in the ECU to adjust the speedo reading on the dash.  You'll have to do some research to see what others with RB swaps have done. 

gap450r
Offline
Last seen: 1 month 3 weeks ago
Joined: 10/27/2018 - 21:33
Thanks, very helpful. I guess

Thanks, very helpful. I guess my only way to go its a dash display.

gap450r
Offline
Last seen: 1 month 3 weeks ago
Joined: 10/27/2018 - 21:33
One last question, for the

One last question, for the traction control, Series 2 can only be setup with one speed sensor or one imput? thinking about running a hall effect sensor on the abs mounts in the diff, do you think thats the best place or the front wheels? thanks.

AEM_NS
Offline
Last seen: 4 hours 8 min ago
Joined: 06/06/2014 - 09:31
Give this thread a read:
gap450r
Offline
Last seen: 1 month 3 weeks ago
Joined: 10/27/2018 - 21:33
Hello, in this section is

Hello, in this section is where I change my pulse per cylinder? If so can you please let me know the steps? Thanks!page1image54700400

 

gap450r
Offline
Last seen: 1 month 3 weeks ago
Joined: 10/27/2018 - 21:33
Dont know if the image went

Dont know if the image went through. Here is the PDF.tach.pdf