102 posts / 0 new
Last post
rookie_45
Offline
Last seen: 4 years 9 months ago
Joined: 05/03/2015 - 09:53
I'm looking for a map

I'm looking for a map
AEM1
7mgte rebuilt stock internals
Metal gasket
FFIM Q45 TB
1200cc injectors
60-1 turbo (I think the A/R is 68 will start to spool at 2800 RPM)

t32265
Offline
Last seen: 4 years 12 months ago
Joined: 05/30/2015 - 14:27
Looking for a calibration

Looking for a calibration file for 30=1401 1994 mustang gt, 363, vic jr heads, vicor efi intake holley 80mm t/b, custom cam 566int. 658ext. 224 @050. 14 lsa, 80lb siemens deka high imp. injectors, 78mm turbo,  gm 3 bar map sensor, ford tfi distibutor, 100 octane fuel. magna fuel 750 fuel pump. Automatic with stall convertor. email is tcrumrine@unitedaccessco.com for easier contact. thanks for any assistance.

 

sen2two
Offline
Last seen: 2 years 3 months ago
Joined: 06/26/2015 - 13:47
I'm looking for  a MAP just

I'm looking for  a MAP just to be able to start and idle.

1995 Mitsubishi 3000GT VR4. Stock block, heads, intake, turbos, fuel, ect. 

GM 3 bar MAP Sensor.

No intercooler or intake pipes (filters on turbo inlet). Full exhaust from turbo back. 

*I will be injecting pre-turbo in the future. But I'll tune for that. I just need a basic start up MAP to get me going.

 

humberto campos
Offline
Last seen: 3 months 2 weeks ago
Joined: 07/04/2014 - 04:44
Hi dears, I'm new but i have

Hi dears, I'm new but i have this startups calib

Dodge
Ford
GM
Honda-Acura
Mazda
Mitsubishi
Nissan
Subaru
Toyota

Startup Calibrations

Thks

DavidCivicSi
Offline
Last seen: 4 years 10 months ago
Joined: 07/20/2015 - 22:28
I need S1 startup calibration

I need S1 startup calibration for :

1993 Honda Civic EG6 B16A

Garrett GT3076

AEM EMS 30-1060

AEM EPM

AEM Boost Solenoid

AEM IAT

RSX COILS

Rywire coils harness

Rywire OBD1 to OBD2A adapter

Omni power 4 bar sensor

ID1000

98 octane gasoline

Walbro 400lph pump

 

Thanks in advance.

rickcamry15
Offline
Last seen: 4 years 9 months ago
Joined: 08/19/2015 - 07:54
Installed aem fic into 2jzgte

Installed aem fic into 2jzgte / sc400 swap (non vvti/just hoping to control the fuel spray % with the fic, nothing else). engine was running with stock 440cc injectors. Ive since upgraded to 700cc injectors, attempted to adjust the injector fuel map precentages, but the best I can get is starter cranking and occasional backfire.

If anyone can shoot me a map just to get the engine running again, Im hoping to make a copy of it and attempt to refine it, or worst case, it will allow me to drive it the 5 minutesoutside of the neighborhood to a tuner (really dont want to set up having it towed that short of a distance if I can limp it there).

Any help is appreciated. Thanks!

edward santos
Offline
Last seen: 3 years 7 months ago
Joined: 05/23/2014 - 19:59
(30-1100) cal wanted please

(30-1100) cal wanted please

97 supra na-t

aem 3.5 bar map

aem boost control sol. 15 psi

aem ugeo

aem temp sensor

aem fuel pump

fuel lab pressure reg 43lbs

siemens deka 875 high imp

precision 6266 .91 hot side

cometic head gasket 1.5mm

arp head and crank studs

tt pistons

hks 3.5 full exhaust

5 speed mt

thank you for your support

Eddie boost

Fabry
Offline
Last seen: 3 years 8 months ago
Joined: 08/24/2015 - 10:05
Hi there,

Hi there,

I looking for a AtiLag Cal for 30-1810 Subaru Impreza WRX 02.

Need a calibration for work around...

 

Thanks to all!

adamvr4
Offline
Last seen: 4 years 8 months ago
Joined: 09/19/2015 - 04:11
hi need a map for my

hi need a map for my

1311 EMS , 1992 3000gt VR4, with rebuild engine, Walbro fuel pump, 550cc/min injectors RC set, 3.5bar MAP sensor, uego controller, IAT, no cat converter installed, tanabe exhaust, 3sx fuel kit

 

 

Teds88
Offline
Last seen: 4 years 7 months ago
Joined: 09/07/2014 - 04:33
Hi, looking for calibration

Hi, looking for calibration for:

30-1400

1988 Mustang, 331ci, AFR 185, Vortech s-trim @ 10psi, GM 3bar 12223861, 1 3/4 long tube headers, Comp Cam XE274HR-12, 48lb inj., 5 speed

331ci

 

slcdsmmf
Offline
Last seen: 4 years 7 months ago
Joined: 10/07/2015 - 20:15
Calibration please.

Calibration please.
30-1310
97 eagle talon awd 5 speed
6bolt swap,eagle rods,mahle pistons,hks 272 cams,Bosch 1000 cc injectors,stainless steal valves,BC springs/retainers,3g lifters,bronze guides,ARP studs,-6 tank to rail,fpr,300 DW fuel pump,gas 91 octane,precision 57 trim (25psi),SD ,omni 4 bar wired to mdp,iat wired threw maf,3 inch exhaust turbo back,MBC,tial vta bov,fmic 3inch piping,external wastegate 38mm. Thank you!

bayezid.f1
Offline
Last seen: 4 years 7 months ago
Joined: 10/22/2015 - 00:11
EMS 30-1821 

EMS 30-1821 

Subaru STI 2006 
Stock engine
intake and exhaust
need calibration

thanx in advance

okaydel
Offline
Last seen: 4 years 1 month ago
Joined: 04/06/2016 - 17:08
30-1052U, 2005 Honda s2000

30-1052U, 2005 Honda s2000 (AP2), 2.2L (engine f22c), OEM injectors, 93 gasoline, OEM MAP

The car is stock. The 30-1052 file in the calibration folder is for the AP1 (9k redline), I need a starting point for the AP2 (8k redline). This car is NOT drive by-wire.

Nfg177
Offline
Last seen: 4 years 1 month ago
Joined: 04/09/2016 - 21:58
Need a ap1 calibration on has

Need a ap1 calibration on has intake test pipe and exhaust. Everything else is stock

boost4brains
Offline
Last seen: 3 years 8 months ago
Joined: 08/14/2016 - 08:37
hello, i'm having trouble

hello, i'm having trouble finding a setupe calibration for my 2001 subaru

i have the AEM EMS v1 p/n 30-1810 (2002-2005 WRX)

the motor ej20 205 v5(non map sensor/installed 3.5 bar map though)

stock motor with 750cc injectors

walborough 255 fuel pump

20g turbo.

 

i have wired in an ait sensor, and also a map sensor which will be used by the tuner.  

thank you

2001 Subaru RS Coupe EJ207
2001 Lexus IS300 2jz-ge

suncivic215
Offline
Last seen: 1 year 1 month ago
Joined: 08/28/2016 - 07:49
searching for help with a

searching for help with a base start up

30-1020 ems in a 93 honda del sol using a odb1-obd2 jumper harness. 1.6 DOHC 8.9:1 compression. cams: lift/duration: in.456,252; ex 426,249. edelbrock victor X intake 70mm tb. RC 550cc 13 ohm injectors. Omni 4 bar map all other sensors are stock. 93 octane.

suncivic215@yahoo.com

thank you

 
mxced93
Offline
Last seen: 1 year 2 months ago
Joined: 10/14/2016 - 09:31
2jzgte jdmwith stock

2jzgte jdmwith stock headgasket

Injector 440cc

gtx3582r   A/r 1,04

Stock map sensor

Stock coil and ignition bkr8eix

Walbro 450lph pump

On 98 gas 

Thank you

 

19

 

 

phil -w
Offline
Last seen: 3 years 6 months ago
Joined: 10/29/2016 - 15:05
1998 Mitsubishi Evo 5 2.3

1998 Mitsubishi Evo 5 2.3 stroker

series1 1313-

 omni 4 bar  map sensor 

id 1000cc injectors (resistor bypass)

walbro 400 /sytec fpr base fuel pressure 3.5bar /-6 fuel pipes and  return

gsc2 cams 

skunk2 inlet  manifold /70mm throttle body (oem idle stepper)

t3 manifold gtx3576r /0.82 turbine housing /44 mm wastegate /v band out 3 inch

3 port apexi boost solenoid 

 full  3 in exhaust

cop  kit  denso coils(Toyota yaris)

muntaz
Offline
Last seen: 3 years 6 months ago
Joined: 06/26/2015 - 21:24
90 celica 3sgte 

90 celica 3sgte 

need calibration file 

sard denso 800 cc injector  

ebay 320 fuel pump

gm 2 bar map sensor 

everything else is stock 

ill pay for the file if i have to 

ems version 1 for 3sgte celica

muntazshakur@gmail.com

 

alvarocake
Offline
Last seen: 3 years 6 months ago
Joined: 11/07/2016 - 21:37
PLEASE HELP ME

PLEASE HELP ME AEM SERIES 1 30-1100

MY CAR IS A TOYOTA SUPRA ENGINE 2JZGTE USDM MY EMAIL IS alvarocake@gmail.com

 

HELP ME WITH THE CONFIGURATION MAP FOR MY FOLLOWING CONFIGURATION. I LIVE IN HONDURAS AND THE TUNERS IN MY COUNTRY DO NOT EXIST. HELP ME PLEASE

TRANSMISSION R154

KIT CLUCTH competition stage 5
  FIDANZA STEERING WHEEL

TURBO PRECISION A / R .56 HOUSING A / R .72

HKS SEQUENTIAL BLOW OFF VALVE

INTERCOOLER GREDDY

AEROMOTIVE FUEL PRESSURE REGULATOR A1000

HKS  FUEL RAIL

INJECTOR BOSCH 210lb 2200CC

 

Dual COMBUSTIBLE PUMP aem a380

GREEDY BOOST CONTROLLER

HKS TURBO TIMER

tial wastegate

Piston wiseco 86 mm 10.5.1 compression

Eagle forged rod

Brian Crower Cams Stage 3 272

AEM WIDEBAND

3 1 / 2PULG MAGNAFLOW ESCAPE

SPECIAL ESCAPE TO WASTEGATE TIAL

ANY HELP IS VERY APPRECIATED. THANKS! HELP ME

kav747
Offline
Last seen: 3 years 5 months ago
Joined: 12/11/2016 - 18:39
Calibration please.30-131097

Calibration please.
30-1310
97 eclipse gsx 5 speed

Danrohrerauto
Offline
Last seen: 3 years 4 months ago
Joined: 12/06/2016 - 07:15
I need a map for ems p/n 30

I need a map for ems p/n 30-1100. firmware V1.03. 1994 usdm toyota supra TT manual transmission. titan 3.5 bar map sensor. IAT from titan. Factory denso 550cc injectors with new denso fuel pump on 93 octane. Single turbo BW S362SXE. Greddy boost solenoid. fjo wideband. adjustable FPR. Greddy FMIC. factory intake and throttle body. stock long block. new factory coils with iridium plugs.

AEM_NS
Offline
Last seen: 1 day 20 hours ago
Joined: 06/06/2014 - 09:31
Upgrade to v1.19 and load a

Upgrade to v1.19 and load a Supra base cal.

Kyle Quiterio
Offline
Last seen: 3 years 4 months ago
Joined: 08/18/2014 - 20:54
7mgte Aem v1 map cal

7mgte Aem v1 map cal

Built 7mgte 9:0 compression

Brian crower 272 cams

Stock ignition system

1650cc FIC injectors

Aem 5 bar Map sensor

Aem iat sensor

Q45 Throttle body( stock 7mgte Tps)

all other sensors are stock

Anything you can help with i greatly appricate it thank you!

Madnessknight89
Offline
Last seen: 3 years 4 months ago
Joined: 01/31/2017 - 16:14
Need a base map for

Need a base map for

1995 acura integra

12.5:1 comp B20 w/ B16 head stock cams.

stock injectors

aem 320lph fuel pump

straight pipe from 1320 magaphone header

msd sci ignition box w/ exturn coil

 

TD350
Offline
Last seen: 1 year 7 months ago
Joined: 02/01/2017 - 14:13
It's a long shot but:

It's a long shot but:

30-1400

1990 mustang 5.0

Blowthru maf cal'd to 42lb injectors

vortech v1 max 7 psi

trickflow 170's, rpm2 intake, lunati 51014 cam. 

Or a calibration for that minus the vortech and stock 19lb injectors. Thanks!

ace_ayala
ace_ayala's picture
Offline
Last seen: 3 years 3 months ago
Joined: 02/02/2017 - 09:38
Req Cal for JDM K24 (k24A2)

Req Cal for JDM K24 (k24A2) AEM 30-6030 V2

87mm 12.5.1

S2 Tunner cams Stage 3

S2 Alpha Header

Xcessive Standard IM 90 TB

ID Injectors 1000cc

TIA

 

Controlled Motors
Offline
Last seen: 1 year 2 months ago
Joined: 02/11/2017 - 01:16
AEM 30-1603U 

 

 

AEM 30-1603U 

1997 240sx kouki, black top sr20det, gt28/71r, 1000cc bosch injectors high impedence (top feed), AEM CAS trigger wheel, IAT sensor, AEM 3.5 bar map sensor, Walbro 255 fuel pump (43psi base), AEM uego with automapping 

I am looking to get the calibration I need to get vehicle started and idleing. 

LATEST UPDATE I HAVE SENCE BEEN ABLE TO START VEHICLE AND DRIVES OK. RUNS VERY RICH UNDER ANY TYPE OF BOOST BUT A/F'S ARE DECENT UNDER CRUISING SPEEDS / VACUUM.  BUT AFTER INSTALLING THE NEW AEM CAS WHEEL (24-1 50MM) IM HAVING A LITTLE TROUBLE IN TIMING SECTION.. I WOULD STILL LIKE TO HAVE A BASE MAP / CALIBRATION  FOR THE SET UP THAT I POSTED PREVIOUSLY BUT IF NOT ATLEAST HELP WITH IGNITION AFTER INSTALLED NEW CAS WHEEL.  THANK YOU I NEED ASAP.

 

schembri1221
Offline
Last seen: 1 year 10 months ago
Joined: 02/23/2017 - 15:37
just looking for somthing to

just looking for somthing to get it started up

1992 eagle talon 4g63 , block is .30 over the head is ported with 280/280 cams and 1mm bigger valves 

1000 cc inj

gt35r turbo

255 walbro pump

3.5 map , iat and o2 sensor

makaofox
Offline
Last seen: 3 years 3 months ago
Joined: 02/23/2017 - 16:04
Just looking for a start up
Just looking for a start up map to get the car out of the garage and into the trailer to tow to a tuner with a dyno. Any help appreciated, I had a map but car would not idle and ran like garbage. Thank You! email makaofalco @ gmail.com
The serial # is a 1101-0035

1976 Datsun 280z
supra 2jzge na to t 3.0L
2jzge stock ignition set up
-Injector dynamics 1000s 
-Bosch 099 fuel pump
-Aeromotive fuel pressure regulator 43psi
-AEM V1 ecu
-AEM EUGO wideband 
-Holset HE351CW turbo
-2jz supra twin turbo oem gasket
-greddy profec boost controller
-tial BOV think 40 or 50mm and wastegate 40mm 14psi spring
-electric fan controller set to turn fan on at 195* F and turn off at 175* F
-92 Q45 throttle body
-2jzge drift motor fuel rail
-stock 2jzge distributor + igniter 
-spark plugs NGK BKR7E (4644) @ 0.031 gap
-NGK spark plug wires
-93 pump gas 17 gal tank
-3in exhaust
-AEM 5bar map
-GM IAT sensor
-350z 6sp cd009
-NO Idle air control valve
 

Pages