237 posts / 0 new
Last post
Smoked240
Offline
Last seen: 4 years 8 months ago
Joined: 09/25/2015 - 10:54
Just joined hoping an expert

Just joined hoping an expert tuner can help me, I will be in debt to you. I have an S13 with a Rb25det. The Aem S2 is tuned for the following:

To add, My tuner did say it was boost comp tuning. I've read into it some but am new to tuning. I picked up the Aem because I got a killer deal on it. I also remember him saying the injecter duty cycle was under 50% if this helps. He may have locked my map but I'm able to make adjustments off my laptop. 

Series 2 30-6620

Stock rb25 turbo

3bar gm map and AIT

Id1000cc injectors

255lph Fuel pump

adjustable FPR set to roughly 44-48 with vacuum off.

Freddy style intake manifold

3" exhaust.

Tuned on E85 made only 270hp/215tq at 10psi.

Made some minor adjustments and need help tweaking my map to put some miles on before I hit my dyno tuner.

Fresh rebuild and Rb26 rotating assembly.

Precision 6266 on DOC manifold with Tial mvr44 set at about 5-10psi spring pressure

Q45 TB

Tomei Fuel rail

I have seated my rings and the bearings just need to put some more miles on but im worried i'll hurt it.

Idle isn't bad, cruising in vacuum it has a skip. my AFR is jumpy but once I start boosting and hit about .5bar I'm seeing 10.4-12.2 but my gauge is messed up, what I see on the AEMTuner is 11.8-12afr but it's not steady.

I know I must add fuel since I've added a larger turbo but how much and at what load? 

Thank you! Arthur.

(Artskogstad@gmail.com)

005sti
Offline
Last seen: 4 years 7 months ago
Joined: 10/01/2015 - 20:08
AEM 30-6821 05 sti already

AEM 30-6821 05 sti already have the ecu connected and reading the TPS but i need help with an start up map 

  1. FIC 1650cc inj  (E85)
  2. built motor
  3. OMP 4bar map sensor SD
  4. 6466 turbo kit
  5. S2 cams 
  6. aem wide band
  7. walbro 450 intank

please someone help thanks 

 

cj_2jzgte
Offline
Last seen: 4 years 7 months ago
Joined: 10/13/2015 - 18:43
AEM 30-6100

AEM 30-6100

96 gs300

stock aristo 2jzgte non vvti single turbo s366 t4

stock 440cc injectors

stock aristo auto transmission

can you also add 725ID injectors to the list

 

Leboncoin
Leboncoin's picture
Offline
Last seen: 4 years 6 months ago
Joined: 10/12/2015 - 16:15
Hi cj_2jzgte,

Hi cj_2jzgte,

I can help everybody with some 2jz calibrations, startups and injector phasing, I need more data about your build, what kind of Map 3.5 or 5bar sensor, AEM IAT yes or not, Boost solenoid controled by the AEM? 

What kind of injectors did you have installed in the car, the stock ones or the ID725??

After this, send me your email and I'll do something nice for you to drive your car arround but at first not for a full range boosted pulls, thats a task for your tuner!

cj_2jzgte
Offline
Last seen: 4 years 7 months ago
Joined: 10/13/2015 - 18:43
Stock map

Stock map
Stock Iat
Stock injectors

Just need a start up map

Chrisjack1215@yahoo.com

Leboncoin
Leboncoin's picture
Offline
Last seen: 4 years 6 months ago
Joined: 10/12/2015 - 16:15
Sorry for not sending

Sorry for not sending anything to you yet, but Im really busy at work! I'll give you a cal soon!

cj_2jzgte
Offline
Last seen: 4 years 7 months ago
Joined: 10/13/2015 - 18:43
Pm sent

Pm sent

mishellis94
Offline
Last seen: 4 years 5 months ago
Joined: 10/16/2015 - 13:29
AEM EMS V2 30-6030

AEM EMS V2 30-6030

Can someone please send me a base map for Honda Integra Type-R DC5? Can't find anything on calibrations folder apart from Acura RSX K20A2 which its a bit different.

Honda Integra Type-R DC5 JDM Model - 2002

Stock engine - K20A (1998cc)

Stock Injectors - 310CC

95 Octane

AEM V2 Cold Air Intake

Stock MAP Sensor(0.75 Bar - 11PSI)

Thanks in advance.

Please send to m1chal15_94@hotmail.com

boostbuilders
Offline
Last seen: 4 years 7 months ago
Joined: 10/24/2015 - 09:58
Hello Everyonecylin

Hello Everyonecylin

New to this forum and the Aem tuning world. Just finished installing my Aem S2 6050 w/ Dezod PnP to run a 2jzgte VVTI motor.

Motor & accessories:

2jzgte VVTI; AEM S2 6050 W/ Dezod Harness, Aem 5 Bar, Aem AIT

Precision 6262, Front Mount, Walboro 255, Stock 440cc Injectors

I was able to start the car, stays in idle but sounds like its missing a cylinder.

Please help tuning my motor. Any help will be highly appreciated. A map for 15 PSI will be great.

Email: Strenth007@gmail.com

Txt/Call: 347-539-4318

God Bless.

KBaileyInPattaya
KBaileyInPattaya's picture
Offline
Last seen: 4 years 6 months ago
Joined: 07/27/2015 - 06:40
Need startup calibration for

Need startup calibration for a 30-6101. 1996 JDM Supra, 2JZGE N/A Automatic Transmission. Engine, ignition, and fuel system 100% stock. Has 4 inch exhaust, OBX header, no catalytic converters. Thanks so much.

KBaileyInSocal@aol.com

Ill3stdr1ft@yah...
Offline
Last seen: 4 years 6 months ago
Joined: 11/29/2015 - 14:59
AEM V2 30-6100

AEM V2 30-6100

Hello, I really need a drive able 2JZ-GTE base calibration for break-in, and to drive to my tuner.

1993 Toyota Supra 6MT

Engine Mechanical:

Stock bottom end
Tomei 264 cams (9.5mm lift)
Pocket ported head
4in downpipe/exhaust
Modified factory Intake manifold with larger plenum
FP HTA3582R (0.82) T4 open
Twin Tial 44mm wastegates
ID1300
Walbro 416 LPH x2 @ 43,5 base Fuel pressure
92 Oct pump gas

Electronics:

GM 4-port Boost solenoid
AEM 5 Bar
AEM UEGO Wideband
No IAT
Using rear cam angle sensor

Please, any help is really appreciated!

Email: ill3stdr1ft@yahoo.com

Bhamasturbo
Offline
Last seen: 2 years 4 months ago
Joined: 08/19/2015 - 17:19
AEM V2-30-6100, downloaded
AEM V2-30-6100, downloaded latest firmware. Car will not start. Seems to be a fuel pump signal, also windows did not work. 1993 UK Supra 6MT . Starts on factory ECU.

 

Engine Mechanical:

Stock bottom end
BC 264 cams 
stock head, turbos, intake

front mount intercooler
4in downpipe/exhaust
Bosch intank pump @ 43,5 base Fuel pressure
92 Oct pump gas

Electronics:

AEM 5 Bar
AEM UEGO Wideband
No IAT
Please, any help is really appreciated!

Email: etsbahamas@gmail.com

AEM_NS
Offline
Last seen: 1 day 20 hours ago
Joined: 06/06/2014 - 09:31
The 6100 is for US spec cars.

The 6100 is for US spec cars.  Windows not working sounds like an interface problem between the EMS and the car which may be indicative of a wiring difference between UK and US cars.  Probably a good idea to compare the pin outs.  Also, you'll need to troubleshoot the no start problem.  Are you getting crank and cam signals?  Does Stat Sync'd turn on?  What's your cranking fuel pulse width?

Masonnjvo
Offline
Last seen: 2 years 6 months ago
Joined: 11/30/2015 - 19:24
Hello, I have had trouble

Hello, I have had trouble with my car for some time now. Looking to get a driving map so that I can go get my car tuned. The basemap that came with the aem isnt good at all because of the things I have done to my motor.

EMS part number: Driftmotion 30-6050,

Vehicle Year/Manufacturer/Model: 92 SC300

Engine: 1jz 264 BC cams, Holset Hx35

 Injector flow rate: JDM 2jz 440cc

AEM 320lph fuel pump

42 psi base fuel pressure

fuel used 93 octane

MAP sensor: Omni power 3 bar

3" DP and exhaust

2.5" IC piping

Email: d_mas0n@yahoo.com

Bhamasturbo
Offline
Last seen: 2 years 4 months ago
Joined: 08/19/2015 - 17:19
Thank you...got it started

Thank you...got it started and window problem fixed. But it is running very rich. I needed to trim it down -40% to get it to idle. Please send map.

sc363
Offline
Last seen: 4 years 4 months ago
Joined: 01/04/2016 - 08:00
30-6100

Hi, looking for a safe file to drive my project lexus to the tuner.

30-6100

2jz-gte

Stock Block, Stock Cams, Gasoline

Borg Warner S363 

Injector Dynamics 1000cc Injectors

3 Bar Map Sensor Omni Power

450 LPH Walbro Pump

AEM UEGO wired in, no stock 02 sensors.

AEM Boost Solenoid

Deleted IACV

kylecreegan@gmail.com 

Thank You,

Kyle

 

george_m
Offline
Last seen: 4 years 2 months ago
Joined: 01/22/2016 - 09:28
hello i have a non vvti 1jz

hello i have a non vvti 1jz stock throttle body with a holset he351cw turbo, deka 850cc injectors, 3" straight exhust, stock toyota map sensor, and 1zzfe coils, stock cams, on 91 gas, running on a 30-6050 box. been trying to set it up and have it running and driving but its not great the accel tables are wrong and no idea how to get the 02 feed back to work with out ocilating. any help would be apreciated also im a bit unclear on what injector phasing is.

Gamelero@buffalo.edu

JesLet
Offline
Last seen: 9 months 3 weeks ago
Joined: 06/23/2015 - 23:08
EMS PN: 30-6100

EMS PN: 30-6100

1995 Toyota Supra 2JZGTE 3.0 , 6 SPEED, Clutchmasters CM850 twin disks

Mods:

BC 272 cams with BC dual valve springs

1000cc Injector Dynamics

91 octane, AEM methanol kit

5 bar AEM map sensor

SP Quick Spool Valve

Borg Warner S366 .91 AR

Twin Aeromotive 340lph fuel pumps

LQ9 coils with NGK BKR7E plugs , gapped at .25

AEM widebad, AEM AFR, AEM Failsafe for methanol

AEM AIT

lansangdennis@gmail.com

JesLet
Offline
Last seen: 9 months 3 weeks ago
Joined: 06/23/2015 - 23:08
Sorry it is Lansangdennis
edward santos
Offline
Last seen: 3 years 7 months ago
Joined: 05/23/2014 - 19:59
need help i have a 97 supra

need help i have a 97 supra nat aem 30-6101 that i have added is300 vvti coil packs to . the issue im haveing is i do not konw what settings to put in the ems please help

Eddie boost

JesLet
Offline
Last seen: 9 months 3 weeks ago
Joined: 06/23/2015 - 23:08
I got nothing....?

I got nothing....?

boost_shift_boost
Offline
Last seen: 4 years 3 months ago
Joined: 02/19/2016 - 15:19
I am new to AEM and very

AEM 30-6620

I am new to AEM and very exicited to get my car tuned with all the features available to AEM. I am searching for a base tune for my rb26 just to get me to my tuner.

r32 rb26dett

Mods:

built bottom end

holset hx40

tial 44mm wastegate with a 14lb wastegate spring

rc1200 peak & hold injectors

3.5bar AEM map sensor

Walbro 450lph fuel pump

3.5 inch downpipe and exhaust

3 inch intercooler piping

93 octane

stock injector resistor deleted

Any help would be greatly appreciated. 

Thank You,

Matthew

boost_shift_boost@yahoo.com

dariasvvl
Offline
Last seen: 4 years 3 months ago
Joined: 02/24/2016 - 19:34
Can help with base map?

Can help with base map?

AEM EMS2 6600

SR20DE Highport Stock

AEM CDI Coil pack

SR20 Dizzy with AEM Trigger Wheel

AEM 5bar Map

GM IAT Sensor

Walbro 255lph Fuel pump

OEM O2 Sensor

90 octane Fuel

d,ariasl1987@gmail.com

 

Thanks!!!!

r32singh
Offline
Last seen: 4 years 1 month ago
Joined: 04/24/2016 - 03:01
Hi all trying to get my car

Hi all trying to get my car started any help welcome 

30-6620 

1992 R32 Skyline GTR 

Rb26dett 

forged bottom end 

stock cams

id1000 injectors

Aem 3.5 bar map sensor

Walbro 450lph pump

t88h34d turbo

aem meth kit 

98 octane fuel 

luckysagoo32@gmail.com

 

cartros709
Offline
Last seen: 4 years 1 month ago
Joined: 04/25/2016 - 11:49
hey looking for someone who

hey looking for someone who can help with fine tuning my supra. car is runnning off a base tune and has been tuned on road up to 7 lbs but my tuner has moved. there is no fuel map above  7 lbs of boost. im looking for some help with populating the fuel map above that gm 3.5 bar map sensor and iat 

 

aem ems series 2 from drift motion, built 7mgte with .2 over pistons making it 3.1l   ported head bcsprings valves bc 264 cams  decked head and block mhg torqued to 75 ft.lbs forged pistons and rods. 6m crank balanced 550 cc rc fuel injectors aem 320lph fuel pump  and turbosmart fpr

 

shimmed oil pump borg warner s366 airwerks turbo 3.5 inch downpipe and exhaust synchronic 50 ml wastegate hks ssqv bov aem cam gars

DesertAuto
Offline
Last seen: 3 years 6 months ago
Joined: 05/04/2016 - 18:52
Looking for a start up tune.

Looking for a start up tune.  Currently hard/extended start, won't idle and pops back through the intake.

AEM EMS Series 2

2005 Nissan 350z

Japanese non vvti 2jzgte stock internals

Chase Bays 2j engine harness

Injector Dynamics high impedance 1000cc @43psi

AEM 5 bar map (no maf)

91 octane

AEM 320lph fuel pump

Precision single turbo, I believe its a T4 .58 A/R

Supra Store top mount manifold

Stock intake manifold

3in. turbo back exhaust

 3" FMIC

Getrag trans

Tial bov and wastegate

Located in AZ @ 4600' above sea level

Just needing the car to run at idle smoothly to check everything out before its sent off for a dyno tune.

 

Thanks in advance!!!

 

 

 

 

 

 

U_tal
Offline
Last seen: 3 years 11 months ago
Joined: 09/28/2015 - 06:32
 I'm looking for map for my

 I'm looking for map for my  60-3060 97 H22 with all standard except stage 1 Skunk2 cams, car won't stay on idle. Thank you very much 

email: U_tal@hotmail.com Hey guys

 

H2B_NZ
Offline
Last seen: 3 years 11 months ago
Joined: 06/11/2016 - 20:00
Looking for a map to get my

Looking for a map to get my car running right 

AEM EMS V2

Honda Civic EG 

Standard Euro R CL1 Engine

Blox velocity stack

PLM 4-2-1 Headers

Full 2.5 inch exhaust

Please send to Loganmartinhansen@gmail.com

Thanks Guys!

 

Poirier4
Offline
Last seen: 3 years 11 months ago
Joined: 04/27/2016 - 16:05
3SGE BEAMS Engine

3SGE BEAMS Engine

36-2 Crank VR, 1Cam VR, Knock Sensor

Toyota 330cc Injectors

Toyota Coils

GM 4Bar Map

GM IAT Sensor

I was able to build a little bit of a base map, but have no knowledge on how to get injectors and coils to fire I have the fuel inj x open channels, my ignition table is all at 16 which I know is wrong, and I read something about syning the cam crank sensors or something?

If somebody could point me into the right direction thanks

txsoldier90
Offline
Last seen: 3 years 11 months ago
Joined: 07/02/2016 - 23:43
2002 Honda S2000

2002 Honda S2000

aem ems s2 30-6052

f20c

1000cc injectors

borg warner .91 ar

fmic

stock pump

stock rail

forged pistons

forged rods

AEM uego wideband

looking for an 18psi boost level as well as fuel maps

Pages