223 posts / 0 new
Last post
Stealth520
Offline
Last seen: 6 months 1 week ago
Joined: 12/02/2015 - 08:20
Looking for a decent map for

AEM 30-6311 1993 3000gt vr4 map needed

1993 Mitsubishi 3000gt VR4

Built motor bored .1 over and built head 

MHI 16g turbos, ID1000cc injectors, Walbro 450lph pump, ~40psi fuel presusre at idle

AEM 3.5 bar MAP Sensor, AEM IAT, AEM electronic boost controller

E85

 

Any help would be greatly apprecated!!

 

s2kmurph
Offline
Last seen: 6 months 1 week ago
Joined: 04/27/2018 - 14:37
Looking for startup basemap 

Looking for startup basemap 

2002 s2000 turbo 

Aem 30-6052

stock motor, pump 94

s366sxe, ID1050x, aem 340lph pump, 

aem 5bar map, aem electronic boost controller, aem oil pressure 150psi

thanks

boushkaa
Offline
Last seen: 5 months 2 weeks ago
Joined: 03/30/2019 - 16:29
Looking for startup basemap 

Looking for startup basemap 

1971 Datsun 521 with an S13 SR20DET Redtop swap

EMS P/N 30-6601

stock motor, 93 Octane

RS3871 Turbo, DeatschWerks 550cc, fitech 255lph pump 

Z32 MAF, Greddy intake Manifold, stock coil pack, stock fuel rail

 

Not sure what other info would be helpful, just trying to get this thing test fired so I can get to the last few things on the truck.

Have paypal ready as well for your time. But I would appreciate any and all help, thanks

Knox839
Offline
Last seen: 5 months 1 week ago
Joined: 04/15/2019 - 03:17
AEM_NS wrote:

AEM_NS wrote:

Aem 30-6040, Honda Integra DB6, RC750cc high impedance,1.6 liter, 93 octane, Omni 4 bar map sensor.

Billsac
Offline
Last seen: 3 months 4 weeks ago
Joined: 02/24/2019 - 16:52
Need a base map for 1jz 88

Need a base map for 1jz 88 Supra. The engine is a jzz30 with aem v2 pnp from driftmotion. 6050-0032. Aem 5 bar map sensor, 93 octane, drift motion 6262 single turbo, id1050x, 1jz iat sensor, Walbro 255 fuel pump, 3” exhaust, stock coil on plug, stock iacv, uego wide band, stock bottom end and head. 

 

 

Bill Rhodes

khmersupra
Offline
Last seen: 3 months 3 weeks ago
Joined: 05/31/2019 - 08:35
1995 supra 6spd

1995 supra 6spd

stock block

preceision 6766

1000cc (93)

tial 44 wastegate

AEM 5 bar / IAT

or even a base would be appriceated 

email: khoeumt@gmail.com

thy

Travischase
Offline
Last seen: 1 month 3 weeks ago
Joined: 09/27/2018 - 21:11
Hello every one.  I'm hoping

Hello every one.  I'm hoping for a safe base tune for an engine break in on 91 0ctane. Thanks in advance!  My specs are below:

 

EMS II 6620.

1971 240z

Skyline RB25DET swap (series 1)

Bosch 800cc injectors

R35 coil packs

Walbro 255

z32 MAF sensor

Autodream cam trigger

Built bottom end

Bored .20 over

GT30r turbo

Tial MVR wastegate (1.0 bar or 14.5psi spring)

DOC race exhaustr now) manifold

FMIC

P.S. I'm willing to pay :)

EdinR-DrugB
Offline
Last seen: 1 month 4 weeks ago
Joined: 09/23/2018 - 20:40
Hello from Bulgaria,

Hello from Bulgaria,

1994 Toyota Supra single turbo a/t

Stock engine + 264 hks cams

6262 pte turbo

100 Octane fuel

EMS Series 2

30-6100

AEM 3,5 Bar Map sensor

MAC 3 port Solenoid

AEM 320L/h fuel pump

AEM fuel pressure on round about 44PSI

stock injectors

AEM Air temp Sensor

AEM type wideband uego controller

4" AEM intake

HKS 50 mm wastegate spring works on 16psi

thanks in advance :-)

S2K_greggie
Offline
Last seen: 1 week 1 day ago
Joined: 08/05/2019 - 19:11
Looking for first time start

Looking for first time start up on;

AEM V2 30-6052

2001 Honda s2000

10lbs of Boost

Internal Wastegate

Turbo t518z

340 LPH fuel pump

550cc Bosch Injectors (52lb)

3 bar MAP

Stock Pressure Regulator

Stock Exhaust

 

alxch
alxch's picture
Offline
Last seen: 3 weeks 2 days ago
Joined: 10/30/2017 - 08:29
BASE MAP FOR SUPERCHARGED JDM

BASE MAP FOR SUPERCHARGED JDM INTEGRA TYPE R

Hello from Guatemala

30-6060 EMS V2,

1996 JDM HONDA INTEGRA TYPE R,

1.8L (Japanese B18CJ, "GSR" Intake CAM, "ITR" Ex. CAM, ported head),  Head Gasket 81.00mm Bore, 0.051 inch compressed thickness

Jackson Racing Supercharger, CR-V Crank size pulley,

750cc Injectors, 95 octane pump gas, AEM Methanol kit, 450 LPH Walbro fuel pump, AEM high volume fuel pressure regulator

Rywire CoP Harness (EPM trigger), Kseries coils, AEM EPM,

Stock Honda MAP sensor, Innovate 3855 Air/Fuel analog gauge (02 Sensor), Innovate 3857 Boost gauge Analog,  AEM 30-3020 Water - Methanol FAILSAFE, AEM Oil pressure gauge 30-5133,

CT Engineering Air box and filter with stock ITR intake pipe

skunk alpha2 headers, 2.5inch custom straight pipe, borla xs muffler,

A base map would be highly appreciated

Thanks in advance

 

Email: wrx_023@hotmail.com

 

Mike_em17
Offline
Last seen: 3 weeks 1 day ago
Joined: 08/25/2019 - 21:58
EMS2 30-6030 standalone

EMS2 30-6030 standalone

HONDA FIT 2014 [L15A ]

stock injectors

stock map sensor

would like a base map for L15A engine

 

Email: Mike_em17@hotmail.com

Mike

Snoik
Offline
Last seen: 4 days 20 hours ago
Joined: 09/12/2019 - 07:13
Hi! I need calibration for 30

Hi! I need calibration for 30-6100:

2JZ-GTE VVTI

stock head

3 bar omni map sensor

a/t 341

borg warner efr 8374 1.05 ar twin scroll

stock 3 coils

bosch 1000 cc injectors

1jz-gte vvti stepper idle

snoik@yandex.ru

Thanks!

Pages